Micromod MOD: 30ML Operation and Template Setup Manual do Utilizador descarregar pdf (Página 22)

MOD 30ML Operation

SETUP

2-12

Table 7. System Template Configuration (Cont’d)

Step Step Description Line 1 Line 2 Line 6 Entry Description

7C System Passwords (Entry)

∇ moves down to Step 7C1

NXT, PRV change step

SYSTEM PASWORDS

The passwords set here will restrict

access to tuning and configuration

features.

7C1 Tune Passwords

∇ ∆ changes number, ENT enters

NXT, PRV change step

TUNE PASSWORD 0

Enter a number required to access

tuning parameters.

7C2 Configure Passwords

∇ ∆ changes number, ENT enters

NXT, PRV change step

CONFIG PASSWORD 0

Enter a number required to access

configuration parameters.

7C3 Access Timeout

∇ ∆ changes number, ENT enters

NXT, PRV change step

ACCESS TIMEOUT 0

0-54 minutes; 0=infinite

The time in minutes that the tune

and configure access levels will

timeout and return to the operate

level after last keyboard activity.

7C4 System (Passwords Exit)

∆ moves up to Step 7C

NXT, PRV change step

SYSTEM

7D System Alarms (Entry)

∇ moves down to Step 7D1

NXT, PRV change step

SYSTEM ALARMS

Alarm indication rates apply to

light, display and beeper. Alarms

are: unacknowledged diagnostics,

high or low process and deviation

conditions, and input quality.

7D1 Diagnostic Flash/Beep Rate

∇ ∆ change value, ENT enters

NXT, PRV change step

DIAGNSTC RATE FAST

FAST = off 100msec, on 300 msec

SLOW = off 250msec, on 750msec

7D2 Diagnostic Flash

∇ ∆ change value, ENT enters

NXT, PRV change step

DIAGNSTC FLASH OFF

OFF = flashing is disabled

ENABLE = flash display (LED

always flashes for diagnostic)

7D3 Diagnostic Beep

∇ ∆ change value

DIAGNSTC BEEP ENABLE

OFF = beeping is disabled

ENABLE = beep for diagnostic

7D4 Minimum Low Alarm Priority

∇ ∆ change value, ENT enters

NXT, PRV change step

MINIMUM LOW PRI 100

All process alarms with priority >=

this value (2 - 255) are considered

LOW priority for display purposes.

7D5 High Priority Process Alarm Flash/

Beep Rate

∇ ∆ change value, ENT enters

NXT, PRV change step

HIGH PRI RATE FAST

FAST = off 100msec, on 300 msec

SLOW = off 250msec, on 750msec

7D6 High Priority Process Alarm Flash

∇ ∆ change value, ENT enters

NXT, PRV change step

HIGH PRI FLASH OFF

OFF = flashing is disabled

ENABLE = flash display on alarm

7D7 High Priority Process Alarm Beep

∇ ∆ change value, ENT enters

NXT, PRV change step

HIGH PRI BEEP OFF

OFF = beeping is disabled

ENABLE = beep on alarm

7D8 Low Priority Process Alarm Flash/

Beep Rate

∇ ∆ change value, ENT enters

NXT, PRV change step

LOW PRI RATE SLOW

FAST = off 100msec, on 300 msec

SLOW = off 250msec, on 750msec

7D9 Low Priority Process Alarm Flash

∇ ∆ change value, ENT enters

NXT, PRV change step

LOW PRI FLASH OFF

OFF = flashing is disabled

ENABLE = flash display on alarm

1 2 ... 17 18 19 20 21 22 23 24 25 26 27 ... 83 84

Comentários a estes Manuais

Sem comentários