Micromod MOD: 30ML Operation and Template Setup Manual do Utilizador descarregar pdf (Página 17)

MOD 30ML Operation

SETUP

2-7

Table 2. Device Setup (Cont’d)

Step Step Description Line 1 Line 2 Line 6 Entry Description

2A Setup Built-in Communications

∇ moves down to Step 2A1 if

jumper is on ICN or 2A3 if jumper

is on RS232, or RS485.

NXT, PRV change step

SETUP BI COMM

Except for the address, built-in

communication parameters can be

changed while the instrument state

is RUN. Address changes require

that the instrument be in the

DEFAULT state (See Note) or with

port status set off after power up

and SCRV switch set (LHD or DEF

state).

2A1

Set ICN Address

∇ ∆ changes number, ENT enters.

NXT, PRV change step

BI ICN 1 ADDRESS 15

ICN address can be 0 to 15. Can

be set when the instrument is in the

DEFAULT state (See Note

Communication jumper set on the

ICN position.

2A2 Set ICN Status Active

∇ ∆ selects YES/NO, ENT enters.

NXT, PRV change step

BI ICN 1 ENABLED

ENABLE?

ENABLED = Active. To make

inactive, power up with SCRV

switch set. ENABLE? = Inactive.

Select YES to make it active.

2A3

Set Modbus Address

∇ ∆ changes number, ENT enters.

NXT, PRV change step

BI MSC 1 ADDRESS 247

Modbus address can be 1 to 247.

Can be set when the instrument is

in the DEFAULT state.

Communication jumper set on

RS232, or RS485 position.

2A4

Set Modbus Baud Rate

∇ ∆ changes rate, ENT enters.

NXT, PRV change step

BI MSC 1 BAUDRATE 9600

150, 300, 600, 1200, 2400, 4800,

9600, 19200, 38400

2A5

Set Modbus Parity

∇ ∆ changes parity, ENT enters.

NXT, PRV change step

BI MSC 1 PARITY NONE

None. Odd, Even

2A6

Set Modbus Stopbits

∇ ∆ changes stopbits, ENT enters.

NXT, PRV change step.

BI MSC 1 STOPBITS 1

1, 2

2A7 Set Modbus Status Active

∇ ∆ selects YES/NO, ENT enters.

NXT, PRV change step

BI MSC 1 ENABLED

ENABLE?

ENABLED = Active. To make

inactive, power up with SCRV

switch set. ENABLE? = Inactive.

Select YES to make it active.

2A8 Setup Communication (Exit)

∆ moves up to Step 2A.

SETUP

2B Password

∇ moves down to Step 2B1

NXT, PRV change step

SETUP PASSWORD

2B1 Password

∇ ∆ changes number, ENT enters

and changes step

PASSWORD 0

Enter a number to change access

to the instrument to None, Tune or

Configure.

2B2 Current Level

ENT goes to step 2B.

CURRENT LEVEL TUNE

NONE an invalid password.

TUNE tune access.

CONFIG configuration access.

2C Setup Device (Exit)

∆ moves up to Step 2

NXT, PRV change step

SETUP *DEVICE*

NOTE: Built-in address cannot be changed if the ICN or MSC block's address within the Main Database is set to a specific number (not

set to "Any"). In order to change the address, the Main Database must first be deleted or a new Database must be downloaded which

has the ICN or MSC block's address configured to "Any".

1 2 ... 12 13 14 15 16 17 18 19 20 21 22 ... 83 84

Comentários a estes Manuais

Sem comentários

Micromod MOD: 30ML Operation and Template Setup Manual do Utilizador Página 17

Comentários a estes Manuais

Manuais e produtos relacionados com Equipamento Micromod MOD: 30ML Operation and Template Setup